2 Connections from 1 Drop

[goinpostal]

I could swear I have seen a splitter that will allow you to plug 2 devices into 1 CAT5 drop, but I cant find one anywhere. Speed is not an issue it only needs to be 10Mbs. A drop is 120.00 and i really don't have need or space for a 4-port hub.

If anyone has any idea where I can find these please "throw me a bone"

------------------
--The Internet -- It's not just for porn anymore!!!

[iateyourcat]

in theory it can be done. it's the same as connecting a crossover cable to a hub but i can't ever remember seeing one.. check out compusa?

------------------
=-iateyourcat-=

[goinpostal]

I think you are referring to "splitting" pairs to run 2 10mbs jacks off of 1 CAT5 cable. I really can't do that because of the building regulations. I have checked CompUsa on-line and even done a google search for "splitters" but all I get are for Lan Analyzers and way too much $$$$$$$.

but thanks "cat"

------------------
--The Internet -- It's not just for porn anymore!!!

[cyberhh]

What exactly are you looking for? You could create a custom harness to go from the 1236 wire standard to 1236 + 4578 harness at both ends and see if it works - just make sure that both harnesses are the same and that pins 123+6 are active on both ends. Also after creating the splitter harness you should use an end to end tester and test the entire run for continuity.

------------------
Death is lighter than a feather - duty heavier than a mountian.

[korpse]

Here's a solution I came up with:

At the patch panel end of the wire run do this: Strip the cat5 cable - punch down 4 wires from the cable into the 10mb blocks on one port and punch the other 4 wires into the 10mb blocks on another port.

At the RJ45 module jack end: Strip the cat5 cable - punch down 4 wires from the cable into the 10baseT blocks on one module and punch the other 4 wires into the 10baseT blocks on another module.

This is basically just a tweak so you dont have to run another wire but it will still use 2 ports on a hub/switch and will only work at 10baseT.

I hope you can understand what I mean...I know it probably sounds confusing.

------------------
"You dumb bastard...it's not a schooner, it's a sailboat!"

[korpse]

<font face="Verdana, Arial, Helvetica, Verdana, Geneva, Arial" size="2">Originally posted by cyberhh:
What exactly are you looking for? You could create a custom harness to go from the 1236 wire standard to 1236 + 4578 harness at both ends and see if it works - just make sure that both harnesses are the same and that pins 123+6 are active on both ends. Also after creating the splitter harness you should use an end to end tester and test the entire run for continuity.

</font>

wow, i totally didnt see your post until after I posted. i feel stupid...

------------------
"You dumb bastard...it's not a schooner, it's a sailboat!"

[Grider]

Check at Datacom Warehouse for the actual splitter thingy.
Datacom warehouse item number DCO1300
Splits a t568b jack into 2 pair 10Base T jacks. $9.99

I would think that you would need two of these to accomplish your goal.

Grider

[goinpostal]

FOUND IT!!!!! this is what I was referring to. I am going to get one and see if they are any good. Thanks for your help.

MFG
http://www.sk-international.com/

Retail
http://www.igo.com/cgi-bin/ncommerce3/ProductDisplay?prmenbr=1&prrfnbr=258830& cat=&subcat=&link= (http://www.igo.com/cgi-bin/ncommerce3/ProductDisplay?prmenbr=1&prrfnbr=258830&cat=&subcat=&link=)

or
www.cyberguys.com (http://www.cyberguys.com) search for Y-NET

------------------
--The Internet -- It's not just for porn anymore!!!

[This message has been edited by goinpostal (edited January 30, 2001).]