-
November 14th, 2002, 07:54 PM
#1
Senior Member
Intel Pentium 3 CPU's
Hi all, I have 7 Intel Pentium Processors that basically I can't get to post (800's 667's 733 and 500).
Is there anyway to find out why they aren't posting (I was given them) And was told that someone had tried to run them in a 100mhz bus board rather than a 133mhz bus...
Would that kill them??
Thanks,
Also, if possible where would I find the pin outs for a socket 370 CPU, I need to know if soldering pins back onto a CPU will work or not..
All sorts of wonderful things in life.
-
November 14th, 2002, 08:13 PM
#2
Registered User
Re: Intel Pentium 3 CPU's
Originally posted by Garak
And was told that someone had tried to run them in a 100mhz bus board rather than a 133mhz bus...
Would that kill them??
Also, if possible where would I find the pin outs for a socket 370 CPU, I need to know if soldering pins back onto a CPU will work or not..
I guess, some of these CPUs are having missed pins?
Try it and let us know...
Running at 100Mhz FSB should not kill the CPU...but bad PSU could do it - have seen it few times...
I would try them in motherboard, what surely support these CPUs - P2B, P2B-F,P3B-F with latest BIOS, and newer...
-
November 14th, 2002, 08:40 PM
#3
Registered User
I was told that putting a high powered Pentium III in a lower powered motherboard would NOT kill the cpu but 'underclock' it. You would wind up with whatever speed is the differential between the current mobo speed and the optimum mobo speed. -In your case about 1/4 less; 800 becomes 600 etc.
As for soldering pins back on, you have more courage than I do Garak!
Orangeman
-
November 14th, 2002, 09:13 PM
#4
Senior Member
-
November 14th, 2002, 09:17 PM
#5
Registered User
Yeah,
You can have mine as soon as it dies on me!!
- Which I think will be in about a week,
Orangeman
-
November 15th, 2002, 07:42 AM
#6
Intel Mod
Garak, there's no reason in principle why soldering a pin back onto a CPU shouldn't be successful when it's a ceramic package. However I don't know how much leeway you'd have with an organic package.
The pins, being gold flashed, will take solder well, but as the surface area to be joined is tiny and solder isn't strong, the joint could break easily.
There is a low temperature silver solder available which is stronger and can be used with a hot soldering iron, but it needs a flux which is somewhat corrosive and would have to have any residue carefully flushed away afterwards.
I'm sure I can remember recovering one CPU this way, I think it was a Cyrix Socket7 chip.
-
November 15th, 2002, 08:56 AM
#7
Re: Intel Pentium 3 CPU's
Originally posted by Garak
Hi all, I have 7 Intel Pentium Processors that basically I can't get to post (800's 667's 733 and 500).
Is there anyway to find out why they aren't posting (I was given them) And was told that someone had tried to run them in a 100mhz bus board rather than a 133mhz bus...
Would that kill them??
Thanks,
Also, if possible where would I find the pin outs for a socket 370 CPU, I need to know if soldering pins back onto a CPU will work or not..
You can find the pinouts on the cpu data sheets here. All I did was a search for cpu pinouts on Intel.com then looked at the PDF. There are missing pins that are called "reserved".
There rest of you questions I believe have been answered. All I can suggest is that if the bios in the board you are testing these on auto detects the chips and you are using chips with a 133 bus, that you turn of auto detect and manually set the chips. Just make sure you set the multiplier the same as they would be if they were in a 133 board. (733 would be 5.5 so it would clock at 550 in the board you are using. and check the voltages.)
-
November 15th, 2002, 10:49 AM
#8
Registered User
hum... i had asked this question a long time ago about soldering a pin on.
i was told, don't do it.....interesting
(_|_) I AM EDITED BY WEBHEAD (_|_)
-
November 16th, 2002, 03:34 AM
#9
Senior Member
Well , if there's physical damage (broken pins etc..) than I guess you can take the risk and try to re-solder them.
However, check with Intel on the warranty - some of your CPUs may be covered and will be replaced.
Better yet, if you're in good terms with a local Intel vendor they might RMA the chips for you..
-
November 17th, 2002, 05:44 AM
#10
I had a P3 800 cpu with a missing pin, and got round it by cuting a piece of hard wire, i.e. a needle and dropping it into hole on zif socket where the missing pin sould be and bingo it booted and has been working great since, it was a bit fiddeley and took about 3 attempts, but much easier than messing about with solder..
-
November 17th, 2002, 11:08 AM
#11
Senior Member
All sorts of wonderful things in life.
-
November 17th, 2002, 07:56 PM
#12
Registered User
Alright, I have an Asus P2B (slot 1) and 2 slot 1 to sckt 370 converters (I've never had op to test them as I've never had a sckt 370 in my possession but I am sure they are fine) so if you want someone to have a test of those cpu's I'll do it.
It would also do me a favor as I have been given several sckt 370 mobo's to test and dont have a cpu.....(am trying to buy one now)
'We apoligise for the inconvienience' Gods final message to his creations.
-
November 17th, 2002, 08:32 PM
#13
Senior Member
Originally posted by vapd
Alright, I have an Asus P2B (slot 1) and 2 slot 1 to sckt 370 converters (I've never had op to test them as I've never had a sckt 370 in my possession but I am sure they are fine) so if you want someone to have a test of those cpu's I'll do it.
It would also do me a favor as I have been given several sckt 370 mobo's to test and dont have a cpu.....(am trying to buy one now)
I'll swap you a cele 500/ cele 700 (known working) for a motherboard Vapd!
Your choice.. as for testing the CPU's I have a board coming in on Wednesday I think.
All sorts of wonderful things in life.
-
December 6th, 2002, 03:22 PM
#14
Acutally, I don't think intel will cover bent pins under warranty -- unless they're damaged in the box (highly unusal). I actually had a processor that had lost a pin and it was in the packaging....even being an IPD, Intel gave us trouble over it.
Craig
-
December 9th, 2002, 01:36 PM
#15
Registered User
Re: Intel Pentium 3 CPU's
Originally posted by Garak
Also, if possible where would I find the pin outs for a socket 370 CPU, I need to know if soldering pins back onto a CPU will work or not..
It WILL work if:
-The CPU is still good AND
-You know how to solder AND
-You don't burn the CPU during soldering
If you have the broken pins it's even better. If not try getting some from a dead CPU that's out of warranty. I think (but i'm not 100% sure that the diameter and length is about the same with the ones 386/486/Pentium have.
Next you'll need some silver-bearing solder, rosin soldering flux, a needle, fine tip tweezers, a soldering iron (35W works fine) and an antistatic wrist. Using the neddle put a tiny amount of flux on the spot where the missing pin is. Make sure your soldering iron has a long enough (and narrow enough) tip to reach that spot. If needed get some 1mm diameter copper wire and wind it on the solderin iron's tip to make a small extension. Clean this tip after it's hot and put a small (I mean small!!!) amount of solder on it. Quickly put the solder where the missing pin is. The flux will ensure that it sticks. Repeat the procedure with the pin that you are going to mount (err... don't hold it with your fingers, it WILL hurt!! ). Now remove the tiny extension from the tip of your soldering iron, grab the pin with the tweezers, put it on the spot where you want it soldered and apply heat on top of it. Having small tweezers will ensure that not all heat gets absorbed and you'll get the solder to melt. Oh... don't forget to wear the antistatic wrist and make sure that your soldering iron's tip is grounded too... static electricity is a killer for semiconductors.
Don't forget you don't want to make a puddle of solder between the pins so just use a very small amount.
If you have previous soldering experience it should be easy (but I assume you don't since you're asking this, so better have someone do it for you).
Good luck and keep us posted
Protected by Glock. Don't mess with me!
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|
Bookmarks