-
June 28th, 2006, 07:44 AM
#16
Driver Terrier
Try it... it either will boot or it won't. It's about the voltage supplied to the processor as well as the bios programming. Got a link to front connector information?
Never, ever approach a computer saying or even thinking "I will just do this quickly."
-
June 28th, 2006, 01:33 PM
#17
Service manual for the Precisioon 410 shoeing pins.
http://www.cs.unc.edu/~jeffay/dirt/F...viceManual.pdf
Cut and paste tha above to IE address bar - it is obviously possible to find Dell Service manuals on line BUT they don't seem to want to let you copy the url for some reason.
Anyway, when it wouldn't ley me copy it, I went to the address line right side, arrowed back, added a single quote, arrowed across, added another single quote, THEN I could copy and paste.
Go figure.
-
June 29th, 2006, 09:27 PM
#18
Registered User
viedo prob
i got the power and leds working, I think, but now i don't have any video. wheh i turn it on it dosn't even give me a single beep unless i have the bios Jumper in the RCVRY Position(according to the board) jumper settings are:
1-2 - normal
2-3 - Config
off - RCVRY
in RCVRY mode the mobo attempts to load a new BIOS from Diskette,
but when after it reads the disk(i Still have no picture durring this)
it gives me a low pitched single beep that repeats until i turn off the system.
power works like it should in the other positions(4-sec hold to turn off)
the only thing that make sense is that it dosn't like my 450 p3
link to user manual is here
http://support.dell.com/support/edocs/systems/dalex/
i've been all around here and the only it says about the power and led connector is here
http://support.dell.com/support/edoc...alex/board.htm
if any one has any opinions or helpful suggestions pls let me know
-
October 5th, 2006, 08:12 PM
#19
Better luck with Intel Type # on underside
I don't know if you folks are still interested after several months... but I just got a similar mobo hand-me-down, and searching E139761 didn't get me anywhere. But the Intel support site recognized a number from the solder (back) side of the board.
Mine is "Intel Type: SE440BX2", right next to the FCC logo, directly opposite the processor's heatsink. Result = PDF product spec (http://www.intel.com/support/motherb...cs-013640.htm).
Hopefully, using your Intel Type # will get the info you're after.
PS- I didn't look up the FSB on a P3-450, but the max FSB on this mobo is 100 MHz.
-
October 5th, 2006, 09:07 PM
#20
Registered User
Originally Posted by MichaelUSA
I don't know if you folks are still interested after several months... but I just got a similar mobo hand-me-down, and searching E139761 didn't get me anywhere. But the Intel support site recognized a number from the solder (back) side of the board.
Mine is "Intel Type: SE440BX2", right next to the FCC logo, directly opposite the processor's heatsink. Result = PDF product spec ( http://www.intel.com/support/motherb...cs-013640.htm).
Hopefully, using your Intel Type # will get the info you're after.
PS- I didn't look up the FSB on a P3-450, but the max FSB on this mobo is 100 MHz.
This thread may have already died.
P3 450 is the first katmai. S spec's are at below website.450 is a 100MHZ.
http://www.cpu-world.com/sspec/Pentium%20III.html
Last edited by street1; October 5th, 2006 at 09:10 PM.
"We Must Have Toliver Gravy!"Said The Bloody
Little Yellow Lumbermen To The Forum King.
-
October 6th, 2006, 03:43 AM
#21
Driver Terrier
Thread may be old, but the information is still relevant for those tinkering with older motherboards. Thanks.
Never, ever approach a computer saying or even thinking "I will just do this quickly."
-
October 6th, 2006, 07:27 PM
#22
Registered User
Originally Posted by NooNoo
Thread may be old, but the information is still relevant for those tinkering with older motherboards. Thanks.
Yes Mam!
"We Must Have Toliver Gravy!"Said The Bloody
Little Yellow Lumbermen To The Forum King.
-
April 1st, 2007, 08:38 AM
#23
I ran across this one too... and its really helped me, I'm tearing apart my daughters old computer, figure if I ruin it, no harm no foul, just trying to teach myself about them, as I'd like to eventually build my own.
I don't even know where to start, but thought I'd just say thanks in advance for all the info I know is here!
-
April 1st, 2007, 08:41 AM
#24
Does anyone know where I can get a block diagram for my motherboard? I think having something show me might be a good start
-
April 2nd, 2007, 07:07 AM
#25
Driver Terrier
Welcome to Windrivers jwisenor
Do you know what motherboard and processor is in this computer? Does it run?
Never, ever approach a computer saying or even thinking "I will just do this quickly."
-
April 2nd, 2007, 08:35 AM
#26
Originally Posted by NooNoo
Welcome to Windrivers jwisenor
Do you know what motherboard and processor is in this computer? Does it run?
As of right now it runs, lol.... but I don't know by the time I get with it. The motherboard is the E139761, thats all I know to tell you, it has a processor that is this one, I'm pretty sure.
http://www.cpupages.com/store/index.php?id_item=613
-
April 3rd, 2007, 04:14 AM
#27
Driver Terrier
Since we know this is an oem board, and your system is running, what brand and model number is it?
Never, ever approach a computer saying or even thinking "I will just do this quickly."
-
July 3rd, 2007, 08:00 AM
#28
-
July 3rd, 2007, 09:27 AM
#29
http://www.tyan.com/archive/products...rinity400.html
Thats general motherboard specs
ftp://ftp.tyan.com/manuals/m_s1854_202.pdf
Thats the PDF Manual including the correct pins for power switch and led etc which is pin compatable with the Dimension D233 (E139761) which ive also found out is a foxconn motherboard design
-
July 3rd, 2007, 12:54 PM
#30
Driver Terrier
Thanks JamieS and welcome to Windrivers!
Never, ever approach a computer saying or even thinking "I will just do this quickly."
Similar Threads
-
By Bjorne in forum Gaming
Replies: 3
Last Post: May 9th, 2004, 05:58 PM
-
By Stu in forum Internet and Networking
Replies: 4
Last Post: December 16th, 2001, 04:18 PM
-
By Skywalker93 in forum Networking
Replies: 7
Last Post: July 21st, 2001, 03:16 PM
-
By chevytoy in forum BIOS/Motherboard Drivers
Replies: 1
Last Post: April 15th, 2001, 07:36 AM
-
By Skywalker93 in forum Tech-To-Tech
Replies: 2
Last Post: April 6th, 2001, 07:29 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|
Bookmarks