-
June 30th, 2005, 05:49 PM
#1
Swapping HD Controller?
I have a Western Digital 40gb hard drive (model WD400BB) with a bad controller board. It has a burned out chip -- actually saw it go up in smoke! I'm wondering if the board can be swapped out with another Western Digital drive? Does the replacement drive have to be of the came capacity? How can I check for firmware compatibility before really messing things up badly? Thanks for any help. Clint
-
June 30th, 2005, 06:13 PM
#2
Geezer
Welcome Clint to wd forums.
Try a read of this thread where we went over the why's & wherefores for somebody else , which I think will help you.
Generally the answer would be to swap out the controller for the exact same model
-
July 1st, 2005, 11:46 AM
#3
In reading the link above and doing a little bit of follow-up research, I've learned that a replacement drive controller may work if it was manufactured about the same time as the failed controller. If the failed drive was partitioned, would that have any bearing on the feasibility of doing a swap?
-
July 2nd, 2005, 12:18 AM
#4
Have you checked your cable that connects the drive to the motherboard?? Sometimes that error is caused when the cable is failing. If the drive has already failed then you would have to find the similar hard drive controller card that is in the drive. Its just a suggestion. Have you had any problems with the DVD or cdrom drive??
-
July 2nd, 2005, 03:01 AM
#5
Geezer
Originally Posted by csr
In reading the link above and doing a little bit of follow-up research, I've learned that a replacement drive controller may work if it was manufactured about the same time as the failed controller. If the failed drive was partitioned, would that have any bearing on the feasibility of doing a swap?
'manufactured about the same time as the controller' ? Mmmm .. if you mean it has to have the same firmware present on host & donor disk, then I agree, if you meant something else, I'm not sure I do ... (sure there are ways to 'cheat' this by doing some re-flashing, or using certain disk tools - but if you have to ask, then I doubt you are ready to try one ! )
'Partitions & whatnot' are part of your system data & stand as much chance of being sucessfully read as anything else 'data' on that disk.
-
July 2nd, 2005, 10:38 AM
#6
My assumption is that if I can find a replacement drive that was manufactured within a few months of my drive, then there is a better chance that the firmware will match up on the controller, thus enabling me to do a controller swap. I read that some other people have been able to do this.
I've read about flashing the firmware to make this work, but I don't have the software to do this and I'm not sure the exact procedures to follow. If anyone has any insight, I'd appreciate it very much. I'm not afraid to try as long as I have good directions.
-
July 2nd, 2005, 05:38 PM
#7
Registered User
Originally Posted by csr
My assumption is that if I can find a replacement drive that was manufactured within a few months of my drive, then there is a better chance that the firmware will match up on the controller, thus enabling me to do a controller swap. I read that some other people have been able to do this.
I've read about flashing the firmware to make this work, but I don't have the software to do this and I'm not sure the exact procedures to follow. If anyone has any insight, I'd appreciate it very much. I'm not afraid to try as long as I have good directions.
With a WD like that you need to find a drive with a simlar model number. They usually end with a A0 A2 or A4. You can use a board from the same revision of the drive. For example I have a WD 200 gig SATA drive. The model number is WD2000JD-00HBB0. If my board fried I would look for a WD SATA drive with a model number ending in HBB0.
Last edited by ironwill99; July 2nd, 2005 at 05:45 PM.
I'm a rage-aholic! I just can't live without rage-ahol! -Homer Simpson
-
July 5th, 2005, 11:56 AM
#8
Thanks for all the feedback. I'm on the search now for a replacement hard drive controller. My 40gb internal Western Digital EIDE hard drive info is as follows:
MDL: WD400BB - 00CLB0 (model number)
DATE: 09 AUG 2001 (date of manufacture)
DCM: RRBHET2AH (?)
Drive Parameters: LBA 78165360
Thanks for any help you can give. My email is: [email protected]
-
July 5th, 2005, 03:21 PM
#9
Registered User
Sunstar micro or ebay is a good place to look. I usually go looking for parts at local "mom and pop" shops first though. The sales guys there look at me like I'm nuts because I want to look through all their drives to find a specific one. In this case you want to find a WD drive with a model number ending in CLB0. If you are going to look around at local shops be sure to write down the numbers you posted to refer to. Hope this helps.
Last edited by ironwill99; July 5th, 2005 at 03:23 PM.
I'm a rage-aholic! I just can't live without rage-ahol! -Homer Simpson
Similar Threads
-
By Sash in forum Windows XP
Replies: 1
Last Post: March 5th, 2005, 01:07 PM
-
By crazyzoop84 in forum USB/Firewire
Replies: 12
Last Post: April 15th, 2004, 06:09 AM
-
By fst1006 in forum Tech-To-Tech
Replies: 12
Last Post: September 19th, 2002, 06:20 PM
-
By DanLuria in forum Hard Drive/IDE/SCSI Drivers
Replies: 11
Last Post: July 27th, 2002, 12:55 PM
-
By Fishyrob in forum USB/Firewire
Replies: 1
Last Post: February 20th, 2000, 04:45 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|
Bookmarks