-
February 11th, 2002, 02:05 AM
#1
New Processor
I'd like to upgrade my processor on my PC.
I've currently got a celeron 450. Not sure what my mobo will upgrade to though. How can I find out?
-
February 11th, 2002, 02:48 AM
#2
Geezer
Easy! post the specs of your motherboard in this thread and wait!
Somebody should be able to tell you the 'fastest' cpu that'll run on your MB
-
February 11th, 2002, 08:08 AM
#3
Chat Operator
[quote]Originally posted by 061070:
I'd like to upgrade my processor on my PC.
I've currently got a celeron 450. Not sure what my mobo will upgrade to though. How can I find out?
Celeron 450? No such CPU my friend. Looks like you have one of the 300A celerons overclocked. Chances are good you have a BX or ZX board. If it's ZX, your out o luck, it will only support mendecino and katmai CPU's, if it's a BX board, it MAY (depends on bios rev and company) support the coppermine CPU's, if that's the case, you can go up to a P3 1000E (remember, no 133 bus)
<Ferrit> Take 1 live chicken, cut the head off, dance around doing the hokey pokey and chanting: GO AWAY BAD VIRUS, GO AWAY BAD VIRUS
-----------------------
Windows 7 Pro x64
Asus P5QL Deluxe
Intel Q6600
nVidia 8800 GTS 320
6 gigs of Ram
2x60 gig OCZ Vertex SSD (raid 0)
WD Black 750 gig
Antec Tri power 750 Watt PSU
Lots of fans
-
February 12th, 2002, 12:48 AM
#4
Had a look at the board and see no serial numbers etc.
Where can I look to find out make etc.
The PC is a Compaq.
-
February 12th, 2002, 02:37 AM
#5
Senior Member
Whats the Compaqs make and model?
All sorts of wonderful things in life.
-
February 12th, 2002, 02:45 AM
#6
Geezer
[quote]Originally posted by Matridom:
Celeron 450? No such CPU my friend. Looks like you have one of the 300A celerons overclocked....
Doubt it....
Celeron 450 benchmark test results
more benchmarks
Mind you if compaq managed a 150% overclock....
Often there is info on the m/b besides serial numbers like multiplier tables and FSB speeds, contained in little tables (almost always in white) any of those....
Read this Motherboard id
This explains about BIOS strings, post that if you can glean no more info from the board...
-
February 12th, 2002, 06:33 AM
#7
Chat Operator
[quote]Originally posted by confus-ed:
Doubt it....
Celeron 450 benchmark test results
more benchmarks
Mind you if compaq managed a 150% overclock....
Often there is info on the m/b besides serial numbers like multiplier tables and FSB speeds, contained in little tables (almost always in white) any of those....
Read this Motherboard id
This explains about BIOS strings, post that if you can glean no more info from the board...
The first link, has part of the intro, they stated that they overclocked CPU's and give a list of CPU's that they used.. 300A was there but no 450... Hmm.. you can see the list here
That second link you have, EVERY single celeron 450 is a 300A overclocked..(look in the notes colum)
Also if you look here there is no celeron 450 accoding to Intel.
The mendecino core was a CPU the Intel NEVER released on the 100 Mhz bus. That cpu IS overclocked (or under clocked)
<Ferrit> Take 1 live chicken, cut the head off, dance around doing the hokey pokey and chanting: GO AWAY BAD VIRUS, GO AWAY BAD VIRUS
-----------------------
Windows 7 Pro x64
Asus P5QL Deluxe
Intel Q6600
nVidia 8800 GTS 320
6 gigs of Ram
2x60 gig OCZ Vertex SSD (raid 0)
WD Black 750 gig
Antec Tri power 750 Watt PSU
Lots of fans
-
February 12th, 2002, 06:43 AM
#8
Registered User
Agree with Matridom here. There never has been a 450Mhz Celeron mass produced by intel. There have been pre-release samples without multiplier locks and this processor could possibly be one of those. As for the board upgrade question, you should be able to put any fcpga celeron 1 in your board(533Mhz $27) but again, I recommend like many others here that you do some research on your board to find out for sure.
Note: To correct display problems, hold the "ALT"key and press"F4".
-
February 12th, 2002, 06:51 AM
#9
Chat Operator
[quote]Originally posted by Gameguru:
Agree with Matridom here. There never has been a 450Mhz Celeron mass produced by intel. There have been pre-release samples without multiplier locks and this processor could possibly be one of those. As for the board upgrade question, you should be able to put any fcpga celeron 1 in your board(533Mhz $27) but again, I recommend like many others here that you do some research on your board to find out for sure.
yup, the 533 would be the highest for sure, but a 450 overlcocked will perform almost the same (100 Mhz bus vs 66 Mhz bus). You could also more than likely go with a P3-600 (no E, no B - hard to find) I'd look well into the board and see what chipset it has... there should be two large chips on the mobo with Intel logos, just post the numbers here...
<Ferrit> Take 1 live chicken, cut the head off, dance around doing the hokey pokey and chanting: GO AWAY BAD VIRUS, GO AWAY BAD VIRUS
-----------------------
Windows 7 Pro x64
Asus P5QL Deluxe
Intel Q6600
nVidia 8800 GTS 320
6 gigs of Ram
2x60 gig OCZ Vertex SSD (raid 0)
WD Black 750 gig
Antec Tri power 750 Watt PSU
Lots of fans
-
February 12th, 2002, 12:43 PM
#10
its a Compaq deskpro
there is a sticker on the mobo with a bar code of somesort.
I can read dw#010178 on it
is this any help guys
-
February 12th, 2002, 04:58 PM
#11
Chat Operator
[quote]Originally posted by 061070:
its a Compaq deskpro
there is a sticker on the mobo with a bar code of somesort.
I can read dw#010178 on it
is this any help guys
Uhm, not really.. get numbers off any of the large IC's.. also, what Model of Compaq deskpro?
<Ferrit> Take 1 live chicken, cut the head off, dance around doing the hokey pokey and chanting: GO AWAY BAD VIRUS, GO AWAY BAD VIRUS
-----------------------
Windows 7 Pro x64
Asus P5QL Deluxe
Intel Q6600
nVidia 8800 GTS 320
6 gigs of Ram
2x60 gig OCZ Vertex SSD (raid 0)
WD Black 750 gig
Antec Tri power 750 Watt PSU
Lots of fans
-
February 12th, 2002, 05:24 PM
#12
doesn't say which version on deskpro it is anywhere.
it has 5 pco slots
2 isa slots
2 dimm slots
2 ide
xu1 processor socket
2 usb
where else can I try
sorry to be vague
-
February 12th, 2002, 05:33 PM
#13
bit more info courtesy of tweak xp
celeron 466mhz chip
original oem
stepping 5
-
February 12th, 2002, 06:42 PM
#14
Chat Operator
Well i think that your Out o luck...
Unless you can get the model number, there is no way to know if there is a bios update to support coppermine. Since you can't tell, then error on safety and say a p3 -600 katmai (512k cache)
If your running at 466, you should see a good boost. Also remember that you may need to get pc100-133 ram. (your ram may only be pc66)
<Ferrit> Take 1 live chicken, cut the head off, dance around doing the hokey pokey and chanting: GO AWAY BAD VIRUS, GO AWAY BAD VIRUS
-----------------------
Windows 7 Pro x64
Asus P5QL Deluxe
Intel Q6600
nVidia 8800 GTS 320
6 gigs of Ram
2x60 gig OCZ Vertex SSD (raid 0)
WD Black 750 gig
Antec Tri power 750 Watt PSU
Lots of fans
-
February 13th, 2002, 12:50 AM
#15
you mean the model number for the PC or the model number for the mobo?
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|
Bookmarks