-
June 21st, 2007, 11:10 PM
#1
Compaq Presario 6000 - dead CPU?
Hello techies,
I am currently working on a Compaq Presario 6000 with an AM37 mobo in it. The system had a dead mobo originally, but I have a new one in it now. The problem is, it boots for a few seconds, all fans turn, then it shuts down (no video). After that, you have to unplug it and plug it back in for it to startup again. This is with a new and tested good power supply, and all cards pulled, floppy unhooked.
Also, when you plug in the power cord, it automatically starts up (no pressing the power button).
This system has a Athlon 2200 in it. I have tried with a different RAM chip, but same results. Have not tried diff CPU yet (don't want to toast one).
Any suggestions? I hate AM3* boards. Such junk....
AW
"It is very dark here. You are likely to be eaten by a grue."
-
June 22nd, 2007, 05:34 AM
#2
Registered User
I would suspect a bad connection of the heatsink / fan and the processor, as it sounds like the heat is turning off the power to save the processor. Did you use thermal paste or a thermal pad? And make sure that the HSF isn't cocked awry on the socket. I would also try another power supply if that isn't the problem as I have seen power supplies tempermental like that in the past. Good luck!
" I don't like the idea of getting shot in the hand" -Blackie in "Rustlers Rhapsody"
" It is a proud and lonely thing, to be a Stainless Steel Rat." - Slippery Jim DiGriz
-
June 23rd, 2007, 05:38 AM
#3
Intel Mod
Have you tried clearing the CMOS in case it's set to un-bootable parameters?
-
June 24th, 2007, 08:48 AM
#4
Driver Terrier
compaqs, I know from experience, have good diagnostics, they will shut down if they detect errors in the hard drive, cd drive or other attached hardware. Pull everything and then see if it will boot and stay alive as well.
Never, ever approach a computer saying or even thinking "I will just do this quickly."
-
June 25th, 2007, 03:35 PM
#5
update - I put in a another new power supply. Unhooked everything for clean boot. Hit the power button, heard my monitor flicker like it was getting a signal. OK, that's normal (didn't actually look at the monitor, mind you). So, unplugged, hooked everything back up. Hit the power switch. Back to staying on for a few seconds, then shutting down. No video. It will not power up again unless I unplug the power supply and re-plug it back in.
I have cleared the CMOS also.
Any more suggestions?
"It is very dark here. You are likely to be eaten by a grue."
-
June 25th, 2007, 04:06 PM
#6
wild idea but you said you put a new mobo in...check and see if you are are grounding out somewhere
-
June 26th, 2007, 07:03 AM
#7
Driver Terrier
And have you booted it with nothing but ram and video connected?
Never, ever approach a computer saying or even thinking "I will just do this quickly."
Similar Threads
-
By bluewest11 in forum AMD
Replies: 52
Last Post: June 2nd, 2007, 02:59 PM
-
By Phaeton in forum Networking
Replies: 2
Last Post: January 15th, 2004, 11:25 AM
-
By ScottieM3 in forum Tech-To-Tech
Replies: 8
Last Post: November 21st, 2001, 05:27 PM
-
By Pinnacle in forum Tech-To-Tech
Replies: 7
Last Post: November 18th, 2001, 09:33 AM
-
By muggins in forum Tech-To-Tech
Replies: 1
Last Post: August 26th, 1999, 07:51 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|
Bookmarks