DVD with Nero Log 2

[stormrider]

I am new to the forum and this is my first post. I have search and read the material I could find but could not resolve.

I am using XP, Nero 7 Burning ROM. What I was trying to do was simply use DVDs and Nero to backup data. I have tried numerous computations with little success. I have been able to backup two disks but not the third, which has video files but well within the limit size of the DVD. I even tried taking one computation that worked [I was successful burning], then deleting some files to make room, then adding a copy of videos. Failed again. From the first to the last, I changed my DMA on the primary IDE [I have two plus one secondary] by deleting the second primary IDE channel and rebooting as the setting for it seemed wrong; no change. BTW, my Advanced tab in all settings has nothing for Device 1, only for Device 0.

Now the strange part. It always crashes at 10 minutes 4 seconds from the start?? I have pasted below a few on the logs to see if this might add more information, or maybe others have had this same problem and have solved it. I have since learned that this post is too long so will add the other two logs separately. [This one is the first failure, the next post the second, and the third and last is a successful burn. Also, I have tried reducing the write speed down to 4X's which is the lowest available but regardless of where and when I change it [from the NEW setup to just before I burn], it always says 16Xs when it starts to burn?? Not sure.

Any help or direction you could give would be very much appreciated.

Thanks.

First burn failure log:
1C80-0010-8010-0000-0003-0535-0074

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 11:54:32 AM

NT-SPTI used
Nero Version: 7.0.1.4
Internal Version: 7, 0, 1, 4

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.0.1.4
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <GJ5211B MDV008R >Version: 1.0 - HA 1 TA 1 - 7.0.1.4
Adapter driver: <SCSI> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 0 ID 0 DMA: Off
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 2 ID 0 DMA: On
DiskPeripheral : MAXTOR 6L080J4 A93. iteraid Port 3 ID 2 DMA: Off
CdRomPeripheral : GJ5211B MDV008R 1.0 dtscsi Port 4 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
GJ5211B MDV008R F: CDRom1
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1023MB (1047788kB)
Free physical memory: 363MB (372452kB)
Memory in use : 64 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

30.1.2007
UDF compilation
6:22:48 PM #1 Text 0 File Isodoc.cpp, Line 6411
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : pure
UDF Revision : 1.02
UDF Partition Type : physical

6:22:49 PM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 262144KB of Memory

6:22:49 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

6:22:49 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

6:22:52 PM #5 Text 0 File Burncd.cpp, Line 3342
Turn on Disc-At-Once, using DVD media

6:22:53 PM #6 Text 0 File DlgWaitCD.cpp, Line 279
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1801551 (400:20.51, 3518MB)

6:22:53 PM #7 Text 0 File DlgWaitCD.cpp, Line 291
Write in overburning mode: NO (enabled: CD)

6:22:53 PM #8 Text 0 File DlgWaitCD.cpp, Line 2578
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

6:22:53 PM #9 Text 0 File DlgWaitCD.cpp, Line 458
>>> Protocol of DlgWaitCD activities: <<<
=========================================

6:22:53 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1801552 (1801552) = #1801552/400:20.52
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1801552 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

6:22:53 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3689578496, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1801552 | lead-out | 1 | 0x41 | 0x00

6:22:53 PM #12 Text 0 File SCSIPassThrough.cpp, Line 36
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

6:22:53 PM #13 Phase 24 File dlgbrnst.cpp, Line 1725
Caching of files started

6:22:53 PM #14 Text 0 File Burncd.cpp, Line 4176
Cache writing successful.

6:22:53 PM #15 Phase 25 File dlgbrnst.cpp, Line 1725
Caching of files completed

6:22:53 PM #16 Phase 36 File dlgbrnst.cpp, Line 1725
Burn process started at 16x (22,160 KB/s)

6:22:53 PM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

6:22:53 PM #18 Text 0 File DVDR.cpp, Line 2580
Recording mode: Sequential Recording Mode

6:22:53 PM #19 Text 0 File MMC.cpp, Line 21611
Set BUFE: Buffer underrun protection -> ON

6:22:53 PM #20 Text 0 File DVDR.cpp, Line 2735
Start write address at LBA 0
DVD high compatibility mode: Yes

6:22:53 PM #21 Text 0 File Cdrdrv.cpp, Line 8411
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

6:32:57 PM #22 SPTI -600 File SCSIPassThrough.cpp, Line 323
D: CdRom0: SCSIStatus(x00) WinError(121) NeroError(-600)
Sense Key: 0x00 (KEY_NO_SENSE)
Sense Code: 0x00
Sense Qual: 0x00
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x00 00 00 00 00 00 00 00 00 00 00 00 00
Buffer x06270000: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

6:32:57 PM #23 CDR -600 File Writer.cpp, Line 302
Device not available
D: HL-DT-ST DVDRAM GSA-4163B

6:32:57 PM #24 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

6:32:57 PM #25 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

6:32:58 PM #26 Text 0 File DVDR.cpp, Line 2978
EndDAO: Last written address was -1

6:32:58 PM #27 CDR -1114 File WriterStatus.cpp, Line 167
Reset occurred
D: HL-DT-ST DVDRAM GSA-4163B

6:32:58 PM #28 TRANSFER -24 File WriterStatus.cpp, Line 167
Could not perform end of Disc-at-once

6:32:58 PM #29 Phase 38 File dlgbrnst.cpp, Line 1725
Burn process failed at 16x (22,160 KB/s)


Existing drivers:
File 'WNASPINT.DLL': Ver=V1.18, size=57344 bytes, created 1/10/2003 12:00:00 AM
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 5/11/2004 9:19:22 PM (Prassi/Veritas driver for win 2K)
File 'Drivers\scsiport.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 8/3/2004 9:59:41 PM (Adapter driver for src)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

[stormrider]

The second failed burn log [which shows this time issues of 10 minutes 4 seconds, as they all do]

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 11:54:32 AM

NT-SPTI used
Nero Version: 7.0.1.4
Internal Version: 7, 0, 1, 4

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.0.1.4
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <GJ5211B MDV008R >Version: 1.0 - HA 1 TA 1 - 7.0.1.4
Adapter driver: <SCSI> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 0 ID 0 DMA: Off
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 2 ID 0 DMA: On
DiskPeripheral : MAXTOR 6L080J4 A93. iteraid Port 3 ID 2 DMA: Off
CdRomPeripheral : GJ5211B MDV008R 1.0 dtscsi Port 4 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
GJ5211B MDV008R F: CDRom1
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1023MB (1047788kB)
Free physical memory: 257MB (263276kB)
Memory in use : 74 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

30.1.2007
UDF/ISO compilation
7:52:43 PM #1 Text 0 File Isodoc.cpp, Line 6411
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : UDF/ISO bridge
UDF Revision : 2.01
UDF Partition Type : physical
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

7:52:43 PM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 262144KB of Memory

7:52:43 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

7:52:43 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

7:52:43 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

7:52:46 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

7:52:46 PM #7 Text 0 File Burncd.cpp, Line 3342
Turn on Disc-At-Once, using DVD media

7:52:46 PM #8 Text 0 File DlgWaitCD.cpp, Line 279
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 772047 (171:33.72, 1507MB)

7:52:46 PM #9 Text 0 File DlgWaitCD.cpp, Line 291
Write in overburning mode: NO (enabled: CD)

7:52:46 PM #10 Text 0 File DlgWaitCD.cpp, Line 2578
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

7:52:46 PM #11 Text 0 File DlgWaitCD.cpp, Line 458
>>> Protocol of DlgWaitCD activities: <<<
=========================================

7:52:46 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 772048 (772048) = #772048/171:33.73
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 772048 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

7:52:46 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 1581154304, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
772048 | lead-out | 1 | 0x41 | 0x00

7:52:46 PM #14 Text 0 File SCSIPassThrough.cpp, Line 36
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

7:52:46 PM #15 Phase 24 File dlgbrnst.cpp, Line 1725
Caching of files started

7:52:46 PM #16 Text 0 File Burncd.cpp, Line 4176
Cache writing successful.

7:52:46 PM #17 Phase 25 File dlgbrnst.cpp, Line 1725
Caching of files completed

7:52:46 PM #18 Phase 36 File dlgbrnst.cpp, Line 1725
Burn process started at 16x (22,160 KB/s)

7:52:46 PM #19 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

7:52:46 PM #20 Text 0 File DVDR.cpp, Line 2580
Recording mode: Sequential Recording Mode

7:52:46 PM #21 Text 0 File MMC.cpp, Line 21611
Set BUFE: Buffer underrun protection -> ON

7:52:46 PM #22 Text 0 File DVDR.cpp, Line 2735
Start write address at LBA 0
DVD high compatibility mode: Yes

7:52:46 PM #23 Text 0 File Cdrdrv.cpp, Line 8411
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

8:02:50 PM #24 SPTI -600 File SCSIPassThrough.cpp, Line 323
D: CdRom0: SCSIStatus(x00) WinError(121) NeroError(-600)
Sense Key: 0x00 (KEY_NO_SENSE)
Sense Code: 0x00
Sense Qual: 0x00
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x00 00 00 00 00 00 00 00 00 00 00 00 00
Buffer x06360000: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

8:02:50 PM #25 CDR -600 File Writer.cpp, Line 302
Device not available
D: HL-DT-ST DVDRAM GSA-4163B

8:02:50 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

8:02:50 PM #27 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

8:02:50 PM #28 Text 0 File DVDR.cpp, Line 2978
EndDAO: Last written address was -1

8:02:51 PM #29 CDR -1114 File WriterStatus.cpp, Line 167
Reset occurred
D: HL-DT-ST DVDRAM GSA-4163B

8:02:51 PM #30 TRANSFER -24 File WriterStatus.cpp, Line 167
Could not perform end of Disc-at-once

8:02:51 PM #31 Phase 38 File dlgbrnst.cpp, Line 1725
Burn process failed at 16x (22,160 KB/s)


Existing drivers:
File 'WNASPINT.DLL': Ver=V1.18, size=57344 bytes, created 1/10/2003 12:00:00 AM
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 5/11/2004 9:19:22 PM (Prassi/Veritas driver for win 2K)
File 'Drivers\scsiport.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 8/3/2004 9:59:41 PM (Adapter driver for src)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

[stormrider]

The third and last log
Successful burn
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 11:54:32 AM

NT-SPTI used
Nero Version: 7.0.1.4
Internal Version: 7, 0, 1, 4

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.0.1.4
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <GJ5211B MDV008R >Version: 1.0 - HA 1 TA 1 - 7.0.1.4
Adapter driver: <SCSI> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 2 ID 0 DMA: On
DiskPeripheral : MAXTOR 6L080J4 A93. iteraid Port 3 ID 2 DMA: Off
CdRomPeripheral : GJ5211B MDV008R 1.0 dtscsi Port 4 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
GJ5211B MDV008R F: CDRom1
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1023MB (1047788kB)
Free physical memory: 303MB (311224kB)
Memory in use : 70 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

31.1.2007
UDF/ISO compilation
9:04:10 AM #1 Text 0 File Isodoc.cpp, Line 6411
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : UDF/ISO bridge
UDF Revision : 1.02
UDF Partition Type : physical
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

9:04:10 AM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 262144KB of Memory

9:04:10 AM #3 Text 0 File Reader.cpp, Line 124
Reader running

9:04:10 AM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

9:04:10 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

9:05:10 AM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

9:05:10 AM #7 Text 0 File Burncd.cpp, Line 3342
Turn on Disc-At-Once, using DVD media

9:05:10 AM #8 Text 0 File DlgWaitCD.cpp, Line 279
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2259999 (502:13.24, 4414MB)

9:05:10 AM #9 Text 0 File DlgWaitCD.cpp, Line 291
Write in overburning mode: NO (enabled: CD)

9:05:10 AM #10 Text 0 File DlgWaitCD.cpp, Line 2578
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

9:05:10 AM #11 Text 0 File DlgWaitCD.cpp, Line 458
>>> Protocol of DlgWaitCD activities: <<<
=========================================

9:05:10 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2260000 (2260000) = #2260000/502:13.25
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2260000 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

9:05:10 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4628480000, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2260000 | lead-out | 1 | 0x41 | 0x00

9:05:10 AM #14 Text 0 File SCSIPassThrough.cpp, Line 36
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

9:05:10 AM #15 Phase 24 File dlgbrnst.cpp, Line 1725
Caching of files started

9:05:10 AM #16 Text 0 File Burncd.cpp, Line 4176
Cache writing successful.

9:05:10 AM #17 Phase 25 File dlgbrnst.cpp, Line 1725
Caching of files completed

9:05:10 AM #18 Phase 36 File dlgbrnst.cpp, Line 1725
Burn process started at 16x (22,160 KB/s)

9:05:10 AM #19 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

9:05:10 AM #20 Text 0 File DVDR.cpp, Line 2580
Recording mode: Sequential Recording Mode

9:05:10 AM #21 Text 0 File MMC.cpp, Line 21611
Set BUFE: Buffer underrun protection -> ON

9:05:10 AM #22 Text 0 File DVDR.cpp, Line 2735
Start write address at LBA 0
DVD high compatibility mode: Yes

9:05:10 AM #23 Text 0 File Cdrdrv.cpp, Line 8411
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

9:05:44 AM #24 Text 0 File Cdrdrv.cpp, Line 1197
09:05:44.328 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

9:10:32 AM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 2260000 (227C20h), length 0 blocks

9:10:32 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

9:10:32 AM #27 Text 0 File DVDR.cpp, Line 2978
EndDAO: Last written address was 2259999

9:10:38 AM #28 Phase 37 File dlgbrnst.cpp, Line 1725
Burn process completed successfully at 16x (22,160 KB/s)


Existing drivers:
File 'WNASPINT.DLL': Ver=V1.18, size=57344 bytes, created 1/10/2003 12:00:00 AM
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 5/11/2004 9:19:22 PM (Prassi/Veritas driver for win 2K)
File 'Drivers\scsiport.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 8/3/2004 9:59:41 PM (Adapter driver for src)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

[NooNoo]

Welcome to Windrivers StormRider

8:02:50 PM #25 CDR -600 File Writer.cpp, Line 302
Device not available
D: HL-DT-ST DVDRAM GSA-4163B

In both your unsuccessful burns, your drive became unavailable.

I am puzzled by your use of the term computation... I don't want to make assumptions at this point, so could you please explain exactly what you mean?

Have you updated your motherboard drivers?

Can you describe you entire IDE configuration please?

[stormrider]

Sorry for the confusion in terms. What I meant to say was 'compilation', which is the term Nero uses to describe the setup on what you are doing, as I understand it. So I have three different ones set up, since I have about 12 gig to backup and want it on 3 separate DVDs.

I have not updated my motherboard drivers. My machine is ASUS 915P ATX Dual DDr PC-Express 1 16X 2 1X 3PCI Sata Raid Sound 100Lan motherboard. It was purchased 2 years ago from a computer outfit that puts together the components you choose. I have 2, 200 gig HDs, 1 80 gig HD, and one DVD/CD . The machine boots from one of the 200 gig drives.

Under Device Manager, the Disk drives are shows as: Maxtor 6 L080j4 SCSI Disk Device; ST3200822AS; ST3200822AS. Under DVD/CD-Rom there are two shown: GJ5211B MDV008R SCSI CdRom Device; HL-DT-ST DVDRAM GSA-4163B. Under IDE ATA/ATAPI controllers, there are 5 shown: Intel 82801FB Ultra ATA Storage Controllers - 2652; Intel 82801FB/FBM Ultra ATA Storage Controllers - 266F; Primary IDE Channel; Primary IDE Channel; Secondary IDE Channel.

One final note. When I went into Computer Management to look at Disk Management, I noticed an additonal DVD listed as F drive [under Properties - General it shows GJ5211B MDV008R SCSI CdRom Device, Device type: DVD?CD-ROM drives, Manufacturer [Standard CD-ROM drives], Location Bus Number 0, Target ID 0, LUN 0; Volumes it states CD-ROM 1 as disk and DVD (F as Type. I forgot all about this which is a virtual DVD installed from Daemon [which I did about a year ago to do some DVD testing]. Not sure what impact this might have??

I hope that is the information that might assist but if not, please let me know.

Thanks very much for helping with this because it is driving me crazy. I appreciate it.

[NooNoo]

Daemon tools can have some odd effects, especially if it has been partially uninstalled.

But I think the problem is with your motherboard drivers. Asus makes several boards with that chipset so here is the intel page instead

Or you can go to Asus and download the drivers based on the motherboard model number.

[stormrider]

Ok, thanks I will try that. I went to both sites and there appears to be a number of drivers you can download, both at Asus and Intel. So could you be a more specific as to which ones you think I should dl, or should I try upgrade everything that is available? [As an example Intel has drivers for the Graphics driver, Intel chipset software installation utility, and Intel Matrix storage technology. Asus has Audio, Bios, Bios-Utilities, Lan, RAID, Utilities, and Other.

And one last thing. If they are wrong for my machine, what will happen? Does the installer check and make sure it is right for the machine??

Thanks again.

[NooNoo]

OK, which motherboard do you have?

[stormrider]

Motherboard - Asus P5GD1.

My bios is 1006 and I understand the latest version is 1014. I have read a bit about flashing it but the directions all assume you have an a: drive which I do not. I do have a disc that came with the board from Asus that has a utility that allows for an option of updating the bios from a file on your HD. Haven't been able to find anything about this but assuming it must be ok if it comes from Asus?? A little worried about flashing it with some of the stories I have heard but maybe no choice now.

thanks again

[NooNoo]

Flashing of bios or firmware of any description carries a risk... if the power goes out when the file is being written, what ever is being written to is toast. Flashing from windows has come along way and is safer than it was... I flashed an intel board this afternoon from windows successfully. I have flashed from the hard drive having booted to dos when there was no floppy drive.

Check the text that comes with the bios update - if you are unaffected by the fixes the bios release is supposed to sort out, don't update.

The P5GD1 comes in 3 flavours. Let's hope you mean the vanilla one... this should be the right one

I am somewhat puzzled about the arrangement of drives and controllers you have.

Under IDE ATA/ATAPI controllers, there are 5 shown: Intel 82801FB Ultra ATA Storage Controllers - 2652; Intel 82801FB/FBM Ultra ATA Storage Controllers - 266F; Primary IDE Channel; Primary IDE Channel; Secondary IDE Channel.

You should have one Controller, one primary and one secondary ide entry.

Are you running windows xp 64bit or 32bit?

[stormrider]

First I am assuming I am running 32 bit because nothing says otherwise.

I am not sure of the controllers and primary secondary since the system creates them, but the configuration that I gave you is correct. Not sure if it makes a difference that one of the drives [could be two of them] is SATA.

Anyway, I thought the first thing I might try in the interim was uninstalling
Daemon because I don't have a current use for it, so just in case it might be causing the problems. Did that then tried burning again. Now it stopped very quickly after it started. I have pasted this log below. So what happened now?

Thanks

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 11:54:32 AM

NT-SPTI used
Nero Version: 7.0.1.4
Internal Version: 7, 0, 1, 4

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.0.1.4
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.0.1.4
Adapter driver: <IDE> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 2 ID 0 DMA: On
DiskPeripheral : MAXTOR 6L080J4 A93. iteraid Port 3 ID 2 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1023MB (1047788kB)
Free physical memory: 487MB (499396kB)
Memory in use : 52 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

3.2.2007
UDF/ISO compilation
4:45:39 PM #1 Text 0 File Isodoc.cpp, Line 6411
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : UDF/ISO bridge
UDF Revision : 1.02
UDF Partition Type : physical
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

4:45:39 PM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 81920KB of Memory

4:45:39 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

4:45:39 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

4:45:39 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

4:45:42 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

4:45:42 PM #7 Text 0 File Burncd.cpp, Line 3342
Turn on Disc-At-Once, using DVD media

4:45:43 PM #8 Text 0 File DlgWaitCD.cpp, Line 279
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 743695 (165:15.70, 1452MB)

4:45:43 PM #9 Text 0 File DlgWaitCD.cpp, Line 291
Write in overburning mode: NO (enabled: CD)

4:45:43 PM #10 Text 0 File DlgWaitCD.cpp, Line 2578
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

4:45:43 PM #11 Text 0 File DlgWaitCD.cpp, Line 458
>>> Protocol of DlgWaitCD activities: <<<
=========================================

4:45:43 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 743696 (743696) = #743696/165:15.71
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 743696 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

4:45:43 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 1523089408, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
743696 | lead-out | 1 | 0x41 | 0x00

4:45:43 PM #14 Text 0 File SCSIPassThrough.cpp, Line 36
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

4:45:43 PM #15 Phase 24 File dlgbrnst.cpp, Line 1725
Caching of files started

4:45:43 PM #16 Text 0 File Burncd.cpp, Line 4176
Cache writing successful.

4:45:43 PM #17 Phase 25 File dlgbrnst.cpp, Line 1725
Caching of files completed

4:45:43 PM #18 Phase 36 File dlgbrnst.cpp, Line 1725
Burn process started at 4x (5,540 KB/s)

4:45:43 PM #19 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

4:45:43 PM #20 Text 0 File DVDR.cpp, Line 2580
Recording mode: Sequential Recording Mode

4:45:43 PM #21 Text 0 File MMC.cpp, Line 21611
Set BUFE: Buffer underrun protection -> ON

4:45:43 PM #22 Text 0 File DVDR.cpp, Line 2735
Start write address at LBA 0
DVD high compatibility mode: Yes

4:45:43 PM #23 Text 0 File Cdrdrv.cpp, Line 8411
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

4:46:04 PM #24 SPTI -1194 File SCSIPassThrough.cpp, Line 323
D: CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1194)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x73
Sense Qual: 0x04
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 10 32 38 00 0C 73 04
Buffer x05400000: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

4:46:04 PM #25 CDR -1194 File Writer.cpp, Line 302
PMA update failure
D: HL-DT-ST DVDRAM GSA-4163B

4:46:04 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

4:46:04 PM #27 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

4:46:04 PM #28 Text 0 File DVDR.cpp, Line 2978
EndDAO: Last written address was -1

4:46:04 PM #29 CDR -1194 File WriterStatus.cpp, Line 167
PMA update failure
D: HL-DT-ST DVDRAM GSA-4163B

4:46:04 PM #30 TRANSFER -24 File WriterStatus.cpp, Line 167
Could not perform end of Disc-at-once

4:46:04 PM #31 Phase 38 File dlgbrnst.cpp, Line 1725
Burn process failed at 4x (5,540 KB/s)


Existing drivers:
File 'WNASPINT.DLL': Ver=V1.18, size=57344 bytes, created 1/10/2003 12:00:00 AM
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 5/11/2004 9:19:22 PM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

[NooNoo]

4:46:04 PM #25 CDR -1194 File Writer.cpp, Line 302
PMA update failure
D: HL-DT-ST DVDRAM GSA-4163B


There are a number of causes of this..
You have version 7.0.1.4 - Nero is up to version 7.7
Time for an update I think here is how

[stormrider]

OK, so I uninstalled Nero, reinstalled it, all after I flashed BIOS. I am now running the most recent version 1014. But still have problems as you can see by my latest long - and this one is different yet, although it has the same issue of resetting at exactly 10:04 after the start. Still don't understand that.

And, after the new BIOS, I now have 2 controllers and 2 primaries and 2 secondaries [added another secondary]. So now I am even more confused but no closer to being able to burn some ordinary data using Nero. Does this log tell you anything more??

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero Version: 7.0.1.4
Internal Version: 7, 0, 1, 4

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.0.1.4
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.0.1.4
Adapter driver: <IDE> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 2 ID 0 DMA: On
DiskPeripheral : MAXTOR 6L080J4 A93. iteraid Port 4 ID 2 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1023MB (1047788kB)
Free physical memory: 300MB (308168kB)
Memory in use : 70 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

4.2.2007
UDF/ISO compilation
8:45:56 PM #1 Text 0 File Isodoc.cpp, Line 6411
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : UDF/ISO bridge
UDF Revision : 1.02
UDF Partition Type : physical
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

8:45:57 PM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 262144KB of Memory

8:45:57 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

8:45:57 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

8:45:57 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

8:45:59 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

8:45:59 PM #7 Text 0 File Burncd.cpp, Line 3342
Turn on Disc-At-Once, using DVD media

8:46:00 PM #8 Text 0 File DlgWaitCD.cpp, Line 279
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 743695 (165:15.70, 1452MB)

8:46:00 PM #9 Text 0 File DlgWaitCD.cpp, Line 291
Write in overburning mode: NO (enabled: CD)

8:46:00 PM #10 Text 0 File DlgWaitCD.cpp, Line 2578
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

8:46:00 PM #11 Text 0 File DlgWaitCD.cpp, Line 458
>>> Protocol of DlgWaitCD activities: <<<
=========================================

8:46:00 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 743696 (743696) = #743696/165:15.71
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 743696 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

8:46:00 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 1523089408, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
743696 | lead-out | 1 | 0x41 | 0x00

8:46:00 PM #14 Text 0 File SCSIPassThrough.cpp, Line 36
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

8:46:00 PM #15 Phase 24 File dlgbrnst.cpp, Line 1725
Caching of files started

8:46:00 PM #16 Text 0 File Burncd.cpp, Line 4176
Cache writing successful.

8:46:00 PM #17 Phase 25 File dlgbrnst.cpp, Line 1725
Caching of files completed

8:46:00 PM #18 Phase 36 File dlgbrnst.cpp, Line 1725
Burn process started at 16x (22,160 KB/s)

8:46:00 PM #19 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

8:46:00 PM #20 Text 0 File DVDR.cpp, Line 2580
Recording mode: Sequential Recording Mode

8:46:00 PM #21 Text 0 File MMC.cpp, Line 21611
Set BUFE: Buffer underrun protection -> ON

8:46:00 PM #22 Text 0 File DVDR.cpp, Line 2735
Start write address at LBA 0
DVD high compatibility mode: Yes

8:46:00 PM #23 Text 0 File Cdrdrv.cpp, Line 8411
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

8:56:04 PM #24 SPTI -1114 File SCSIPassThrough.cpp, Line 323
D: CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1114)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x70 00 06 00 00 00 00 10 00 00 00 0C 29
Buffer x05200000: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

8:56:04 PM #25 CDR -1114 File Writer.cpp, Line 302
Reset occurred
D: HL-DT-ST DVDRAM GSA-4163B

8:56:04 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

8:56:04 PM #27 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

8:56:05 PM #28 Text 0 File DVDR.cpp, Line 2978
EndDAO: Last written address was -1

9:43:40 PM #29 CDR -1135 File WriterStatus.cpp, Line 167
Write error
D: HL-DT-ST DVDRAM GSA-4163B

9:43:40 PM #30 TRANSFER -24 File WriterStatus.cpp, Line 167
Could not perform end of Disc-at-once

9:43:40 PM #31 Phase 39 File dlgbrnst.cpp, Line 1725
Burn process aborted


Existing drivers:
File 'WNASPINT.DLL': Ver=V1.18, size=57344 bytes, created 1/10/2003 12:00:00 AM
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 5/11/2004 9:19:22 PM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

[NooNoo]

You uninstalled nero and reinstalled, but did you get the newer version? Updates for nero are free.

[stormrider]

OK, I finally updated Nero to 7.7.5.1 , ran the program and think I got the same results. So the motherboard drivers have been updated, Nero has been updated, the other software has been uninstalled, but still the issue.

I had also tried to simply straight copy a DVD and it seemed to have no problem until about 10 minutes into writing and then it locked. I was not able to get a log from this as it ended up freezing the machine and I had to hard reboot.

Here is the latest log. Any suggestions from here??

Thanks.

Windows XP 5.1
IA32
WinAspi: -

NT-SPTI used
Nero Version: 7.7.5.1
Internal Version: 7, 7, 5, 1

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.7.5.1
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HL-DT-ST DVDRAM GSA-4163B>Version: A100 - HA 1 TA 0 - 7.7.5.1
Adapter driver: <IDE> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 2 ID 0 DMA: On
DiskPeripheral : MAXTOR 6L080J4 A93. iteraid Port 4 ID 2 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 1023MB (1047788kB)
Free physical memory: 426MB (436904kB)
Memory in use : 58 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

22.3.2007
UDF/ISO compilation
9:18:18 AM #1 Text 0 File SCSIPTICommands.cpp, Line 411
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL

9:18:18 AM #2 Text 0 File Isodoc.cpp, Line 6527
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : UDF/ISO bridge
UDF Options : automatic
UDF Revision : 1.02
UDF Partition Type : physical
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

9:18:18 AM #3 ISO9660GEN -11 File Geniso.cpp, Line 3334
First writeable address = 0 (0x00000000)

9:18:18 AM #4 ISO9660GEN -11 File Geniso.cpp, Line 3334
First writeable address = 0 (0x00000000)

9:18:18 AM #5 Text 0 File Burncd.cpp, Line 3465
Turn on Disc-At-Once, using DVD media

9:18:19 AM #6 Text 0 File DlgWaitCD.cpp, Line 306
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 743695 (165:15.70, 1452MB)

9:18:19 AM #7 Text 0 File DlgWaitCD.cpp, Line 318
Write in overburning mode: NO (enabled: CD)

9:18:19 AM #8 Text 0 File DlgWaitCD.cpp, Line 2912
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

9:18:19 AM #9 Text 0 File DlgWaitCD.cpp, Line 490
>>> Protocol of DlgWaitCD activities: <<<
=========================================

9:18:19 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 823
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 743696 (743696) = #743696/165:15.71
relocatable, disc pos for caching/writing not required/ required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 743696 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

9:18:19 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1026
Prepare [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 1523089408, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|__ ____NWA_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 743696 | 0 | 0x00
0 | 1 | 1 | 0x41 | 743696 | 0 | 0x00
743696 | lead-out | 1 | 0x41 | 0 | 0 | 0x00

9:18:19 AM #12 Text 0 File SCSIPTICommands.cpp, Line 209
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

9:18:19 AM #13 Phase 24 File dlgbrnst.cpp, Line 1760
Caching of files started

9:18:19 AM #14 Text 0 File Burncd.cpp, Line 4298
Cache writing successful.

9:18:19 AM #15 Phase 25 File dlgbrnst.cpp, Line 1760
Caching of files completed

9:18:19 AM #16 Phase 36 File dlgbrnst.cpp, Line 1760
Burn process started at 4x (5,540 KB/s)

9:18:19 AM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2764
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

9:18:19 AM #18 Text 0 File DVDR.cpp, Line 3070
Recording mode: Sequential Recording Mode

9:18:19 AM #19 Text 0 File DVDR.cpp, Line 3226
Start write address at LBA 0
DVD high compatibility mode: Yes

9:18:19 AM #20 Text 0 File Cdrdrv.cpp, Line 9288
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

9:19:11 AM #21 SPTI -1194 File SCSIPassThrough.cpp, Line 179
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1194)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x73
Sense Qual: 0x04
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 10 32 38 00 0C 73 04
Buffer x07e50040: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

9:19:11 AM #22 CDR -1194 File Writer.cpp, Line 301
PMA update failure
D: HL-DT-ST DVDRAM GSA-4163B

9:19:12 AM #23 Text 0 File DVDR.cpp, Line 3446
EndDAO: Last written address was -1

9:19:48 AM #24 CDR -1194 File WriterStatus.cpp, Line 162
PMA update failure
D: HL-DT-ST DVDRAM GSA-4163B

9:19:48 AM #25 TRANSFER -24 File WriterStatus.cpp, Line 162
Could not perform end of Disc-at-once

9:19:49 AM #26 Phase 38 File dlgbrnst.cpp, Line 1760
Burn process failed at 4x (5,540 KB/s)

9:19:49 AM #27 Text 0 File SCSIPTICommands.cpp, Line 254
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

9:19:53 AM #28 Text 0 File Cdrdrv.cpp, Line 10529
DriveLocker: UnLockVolume completed

9:19:53 AM #29 Text 0 File SCSIPTICommands.cpp, Line 411
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL


Existing drivers:

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)