COMPAQ Deskpro
Results 1 to 12 of 12

Thread: COMPAQ Deskpro

  1. #1
    Registered User
    Join Date
    Feb 2004
    Posts
    2

    Lightbulb COMPAQ Deskpro

    I have a Compaq Deskpro with a 200 MHz pentium and I want to put a 20 GB hard Disk (Quantum Fireball 20 lct) ! How can I do that ? I need a BIOS update ? From where ...how ?

  2. #2
    Banned
    Join Date
    May 2001
    Location
    North West England.
    Posts
    3,200
    welcome to windrivers paul ,,the machine may be to old to accept a drive of that size ,

    however , there may be other compac techs floating around with more acurate info.

    there are 3 ways i can see of doing this

    1: bios update from compac (hp) http://h18007.www1.hp.com/support/files/

    2: using the h/disk (not h/hisk) mfg h/disk instilation tools , usually available from there website,

    3 using a "promise" type IDE card ,,,although this might sound an expensive way (maybe not thru Ebay) ,,,your board will not be very fast ,,and might not support UDMA 1/2/3/4 etc ,,,whereas a controller card will run at a greater speed than the on-board ,


    good luck


    freddy
    Last edited by freddy; February 24th, 2004 at 10:59 AM.

  3. #3
    Registered User corturbra's Avatar
    Join Date
    Oct 2000
    Location
    Just to the Right of Sanity..
    Posts
    1,424
    Could also search Quantum website for the install wizard for the drive, I think its called something like eazy bios.

  4. #4
    Banned
    Join Date
    May 2001
    Location
    North West England.
    Posts
    3,200
    Quote Originally Posted by corturbra
    Could also search Quantum website for the install wizard for the drive, I think its called something like eazy bios.
    as per suggestion 2 in post above



    freddy

  5. #5
    Registered User hudsonsmith's Avatar
    Join Date
    Feb 2003
    Location
    New York
    Posts
    2,276
    hmmmm....the hard drive might be worth more than the system.

  6. #6
    Registered User flackt's Avatar
    Join Date
    Jan 2001
    Location
    Shumway,IL,USA
    Posts
    66
    The setup information on these old desk pros does not reside in a CMOS chip on the MotherBoard.

    It's kept on a non dos partition on the Hard Drive. So you also need to re create this partition on the new hard drive. You can download a utility from compaqs website that will make boot disks to do this.

    Its called the "system configuration utility"

    I'm guessing this is the right model.

    http://h18007.www1.hp.com/support/fi...ocate/4_7.html



    I had a couple of pallets of these a couple of years ago. I never tried to put a large drive in one though.
    "Really???
    What Fun Is A Computer That Works?!?"

    PLEASE! Do not mistake my laziness for lack of concern!

    Proud member of the Vast Right Wing Conspiracy

  7. #7
    Registered User
    Join Date
    Feb 2004
    Posts
    2
    I know that the Quantum Fireball lct 20 it worths more than that PC ...plus IT DOESN'T MAKES BAD SECTORS ! I don't know how these hard disks can be so resistant

  8. #8
    Registered User ironwill99's Avatar
    Join Date
    Aug 2002
    Location
    <funny location>
    Posts
    143
    Quote Originally Posted by paul666
    I know that the Quantum Fireball lct 20 it worths more than that PC ...plus IT DOESN'T MAKES BAD SECTORS ! I don't know how these hard disks can be so resistant
    Actually the leading cause of death for Quantum drives is the PCB. The chip that is just above the power connector can be fried very easily. I see it happen all the time.

  9. #9
    Registered User
    Join Date
    Oct 2004
    Posts
    3

    Type of Deskpro?

    I have a Compaq Deskpro, and when visiting the HP site to download drivers, it ask what type of series I have. I don't know since there is not other information on the computer. I bought this thing from a friend who needed some money and he didn't have any other information booklets or anything, he said that he had thrown them away long ago, since this thing is about 5 years old. The only thing it shows is has a label for the Microsoft software edition and that it has the Intel Inside Celeron. How do I go about find the seriers version so that I get the right drivers?

    K.D. of Austin, Texas

    list of deskpro

    http://h20180.www2.hp.com/apps/Looku...=6&submit.y=10

  10. #10
    Registered User hudsonsmith's Avatar
    Join Date
    Feb 2003
    Location
    New York
    Posts
    2,276
    Welcome to windrivers tinkertron. On the back of the computer, where all the wires connect, there will be a label with the model # and serial #.

  11. #11
    Registered User
    Join Date
    Oct 2004
    Posts
    3

    Nothing but...

    Quote Originally Posted by hudsonsmith
    Welcome to windrivers tinkertron. On the back of the computer, where all the wires connect, there will be a label with the model # and serial #.
    I see nothing back there other then a sticker with a serial number, that matches the serial number on the top of the computer, No model number. Any other ideas?

  12. #12
    Registered User hudsonsmith's Avatar
    Join Date
    Feb 2003
    Location
    New York
    Posts
    2,276
    Download Everest: http://www.lavalys.com/products/down...ng=en&pageid=3

    Should identify most of your components.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •